← Back to Chevrolet Spark Guides

2013–2015 Chevrolet Spark

2013-2015 Chevrolet Spark — Wiper Blade Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10 minutes $81 DIY

Quick answer: Wiper Blade Replacement on a 2013–2015 Chevrolet Spark is rated Easy and takes about 10 minutes. You'll need 2 tools for this job, and parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$80.97
Part Name Part Number Price Buy
Driver wiper blade, 24" Bosch 24A $32.99
Passenger wiper blade, 16" Bosch 16B $32.99
Rear wiper blade, 12" (hatchback only) — $14.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Buy the right three sizes — and the right connectors

Measure the rubber on your old blades and look closely at the arm tips — if yours have the little push-button on top of the connector, shop for blades that include the matching button adapter.

2

Ignition off, hood closed, arms at park

Turn the ignition off and leave the wiper stalk alone. The Spark's wipers park at the very base of the windshield, below the hood's trailing edge, and both arms lift freely at park — there is no hidden service mode to set on this car. Because the Spark is so small, stand close to the cowl and work one arm at a time. The hood is narrow and light; leave it closed, since you don't need it open for this job. If it's windy, keep a towel draped over each arm while the blades are off so a gust can't slam a bare arm down.

🔧 Mechanic's note — Ray Delgado

Small car, small wiper blades here. I always measure rather than assume — subcompacts vary more than most people think.

3

Release the front blades from the top-button mounts

Lift the driver's arm a few inches off the glass. Press that button down with your thumb and slide the blade toward the base of the arm — the whole blade comes off the arm's flat tab in one motion.

4

Clean the sweep zone and check the arms

Look at the old blades: the driver's 24-inch blade is one of the longer blades for this class of car, and its long rubber wears fastest at the ends.

5

Mount the new 24 and 16 onto the front arms

Line up the new driver's blade (24 inch) with the arm's tab, slide it on, and listen for the button to pop back up through its hole — that pop is your confirmation. Tug the blade firmly; it should not move. Repeat with the 16-inch passenger blade, double-checking the sides: on this car the length difference is huge (eight inches), so a swapped pair is immediately obvious, but check anyway. Keep the protective covers on the rubber until each blade is on the arm. Lower the arms gently onto the glass by hand; don't let them drop under spring tension.

6

Swap the 12-inch rear blade on the hatch

Lift the short rear arm and release its blade the same way as the fronts: press the small button and slide the blade off the tab. Fit the new 12-inch blade until the button clicks, tug to verify, and lower the arm.

7

Test all three and plan the next change

Close the hatch, run the front washers and wipers on low and high, then the rear wiper with its washer. Watch the 24-inch driver's sweep from the seat — it should clear from the A-pillar all the way across your sight line with no chatter.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying classic J-hook blades that don't fit — the 2013–2015 Spark's front arms use a top-button mount, not a hook.
  • • Swapping the 24 and 16 — on this car the driver/passenger length gap is enormous, so check sides before mounting.
  • • Skipping the 12-inch rear blade; it's small but it does the whole job on the hatch glass.