Quick answer: Battery Replacement on a 2019–2024 BMW M5 is rated Moderate and takes about 30–45 minutes. You'll need 7 tools for this job, and parts cost about $147. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Correct group-size battery |
— |
$140.00 |
|
| Terminal cleaner Optional |
— |
$8.00 |
|
| Terminal protectant |
— |
$7.00 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Power down — the M5 uses a lithium-ion battery in the trunk
Park level, brake set, ignition off, key out. Glasses and gloves on. The replacement must be the same lithium-ion type; don't substitute AGM or lead-acid. Gather a 10mm wrench, 13mm socket, trim pry tool, terminal brush, and scan tool.
🔧 Mechanic's note — Tom Becker
I never put a lead-acid battery in this car to save money, and never charge the lithium one on a lead-acid setting — wrong chemistry on the charger is how lithium batteries cook. The replacement must be lithium-ion, full stop.
2
Lift the trunk floor panel to reach the battery
Clear the trunk; lift the floor panel to expose the battery compartment. Remove any cover or trim over the battery, releasing its clips gently with the trim tool. Photograph the orientation and cable layout now — the replacement must sit exactly the same way.
3
Disconnect the terminals, negative first
Loosen the negative terminal nut with the 10mm wrench and ease the cable end off the post, tucking it aside so it cannot touch the battery again. Then disconnect the positive cable.
🔧 Mechanic's note — Ray Delgado
I always treat every tool like it's live around this battery — a wrench bridging the terminals on a lithium pack doesn't spark, it welds. Keep the loose positive end covered with a rag the whole time.
4
Unbolt the hold-down and lift out the old battery
Unbolt the hold-down clamp or bracket securing the battery — typically a 13mm bolt — and lift it clear. If a vent tube is fitted to the battery, pull its elbow off and note the routing. Lift the old lithium battery straight up and out of the well. It will feel surprisingly light compared with a conventional battery — that is normal. Compare it side by side with the new one: same size, same terminal layout and polarity, same lithium-ion chemistry.
5
Install the new lithium battery and refit the hold-down
Lower the new lithium-ion battery into the well in exactly the same orientation as the old one. Refit the hold-down clamp or bracket and tighten its bolt until the battery is completely immobile — even a light battery must not be able to shift.
6
Reconnect positive first, negative last
Reconnect in reverse order: positive (red) cable first, then negative (black) last. Tighten each 10mm nut until the cable end is snug and cannot be twisted on the post by hand. A light coat of terminal protectant helps keep the connections clean. Double-check that the cables follow their original routing and that nothing is pinched when the cover and floor panel go back on. Never jump-start or charge this battery with equipment set for lead-acid — any charger used must have a lithium mode.
7
Register the new battery with a scan tool
The F90’s power management is calibrated for this specific lithium-ion battery, so register the new battery with a diagnostic scan tool per your owner’s manual — a dealer or BMW specialist can do this if you do not have the tool.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Installing a conventional AGM or lead-acid battery — the F90 M5 needs the same lithium-ion type it came with.
- • Charging the new battery with a charger set to lead-acid mode instead of its lithium setting.
- • Forgetting that lithium batteries are far lighter and smaller-feeling than expected, then doubting the fit — match it to the old battery and the tray.
- • Skipping registration — the car’s charging strategy is calibrated for this specific battery.