EZCarFix DIY Auto Repair
← Back to Chevrolet Caprice Guides

2011–2017 Chevrolet Caprice

2011-2017 Chevrolet Caprice — Wiper Blade Replacement

By Tom Becker ✓ Certified Mechanic · Published Sep 21, 2026 · Updated Oct 22, 2026

🔧 Easy 10–15 minutes $66 DIY

Quick answer: Wiper Blade Replacement on a 2011–2017 Chevrolet Caprice is rated Easy and takes about 10–15 minutes. Parts cost about $66. This guide walks you through the full job step by step, including the mistakes to avoid.

Quick Video Tutorial

Parts You Need

Total Cost
$65.98
Part Name Part Number Price Buy
Driver wiper blade, 26" Bosch 26A $32.99
Passenger wiper blade, 15" Bosch 15B $32.99

About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.

💡 Pro tip: Order all parts at once to save on shipping

Step-by-Step Instructions

Follow these steps carefully

1

Buy the 26-and-14 pair — and mind the connector

The Caprice PPV takes a 26-inch blade on the driver side and a 14-inch blade on the passenger side. GM's own parts data lists them at 25.59 and 14.96 inches, which the aftermarket rounds to 26 and 14. The critical detail is the connector.

2

Shut the car down completely

Ignition off, key or fob out of range, wiper stalk confirmed off. Many of these cars lived as patrol vehicles with upfitter wiring, so double-check nothing is keeping accessory power alive.

3

Release the long driver's blade

Lift the driver's arm away from the glass and keep a firm grip on it. The new one must go back the same way, spoiler lip facing up the windshield.

4

Click the new 26-inch blade on

Take the new 26-inch blade and slide its adapter straight up the arm's tongue until the pinch tabs snap outward with an audible click. Because this blade is so long, support it mid-blade while you work so it does not lever against the connector.

5

Fit the short passenger blade

Repeat the pinch-and-slide release on the passenger arm and fit the 14-inch blade. Do not mix the sides up — the 26-inch blade belongs on the driver side, and the size difference here is dramatic enough that a swap is obvious, but check anyway. Seat the adapter until it clicks, tug-test it, remove the sleeve from the rubber, and lower the arm gently. Wipe the glass under both arms with glass cleaner while you have the access; ex-patrol cars often have a film of grime where the blades park.

6

Verify the adapters and arm condition

Look closely at both connectors: the pinch tabs must be visibly snapped outward on each side of the arm's tongue, with no gap and no wobble. If you bought multi-adapter blades, confirm the pinch-tab adapter is the one actually fitted — the J-hook and side-pin adapters in the box do not belong on this car. Sight down each arm for straightness; a patrol car that brushed a car-wash track or an ice scraper can have a bent arm that no blade will fix.

7

Test with washers at all speeds

Turn the ignition on and run the washers, watching the long driver blade sweep its full arc. If a blade skips or streaks, lift the arm and re-seat the tabs. When both blades wipe clean and quiet, the job is done.

All Done!

Test your repair before closing everything up. If something doesn't work right, double-check your steps.

⚠️ Common Mistakes to Avoid

  • • Buying J-hook blades for pinch-tab arms — the Caprice needs the pinch-tab/top-lock fitting
  • • Fitting a multi-adapter blade with the wrong adapter pre-installed
  • • Swapping the 26-inch and 14-inch blades between sides
  • • Skipping the tug test on the pinch tabs — the long driver blade flies off at speed if unlatched
  • • Leaving the protective sleeve on the new rubber edge