Quick answer: Wiper Blade Replacement on a 2006–2011 Chevrolet HHR is rated Easy and takes about 10–15 minutes. Parts cost about $81. This guide walks you through the full job step by step, including the mistakes to avoid.
| Part Name |
Part Number |
Price |
Buy |
| Driver wiper blade, 18" |
Bosch 18A |
$32.99 |
|
| Passenger wiper blade, 18" |
Bosch 18B |
$32.99 |
|
| Rear wiper blade, 11" |
— |
$14.99 |
|
About prices: shown prices are typical retail averages and change frequently; cheaper alternatives may be available. Confirm the current price before buying.
💡 Pro tip: Order all parts at once to save on shipping
Step-by-Step Instructions
Follow these steps carefully
1
Confirm the HHR’s sizes before you buy
Every 2006–2011 HHR takes 18-inch blades on both front sides, so the long-versus-short trick won't help. Rear: 11 inches (2006–2009) or 12 inches (some 2010–2011s); measure the old blade. The rear Roc Loc 2 mount needs a vehicle-specific blade.
2
Park and lift the front wiper arms
Park on level ground, ignition off, parking brake set. Lift each cowl-parked arm until the spring holds it standing — no service position. Lay the two new 18-inch blades side by side first so you know they match.
3
Remove the driver-side 18-inch blade
Fold the driver's arm up and rotate the blade perpendicular. Press the release tab, slide the blade off the hook, keeping the old blade in its spot as a placeholder. Lay a towel under the bare arm before letting go.
🔧 Mechanic's note — Ray Delgado
In my experience, Since both front blades are 18 inches, don't toss both old ones in one pile — keep the driver's-side old blade in its spot as a placeholder so you never mix up which side you're on.
4
Install the new driver-side 18-inch blade
Slide the new 18-inch blade onto the J-hook until it clicks over the locking tab. Tug along the arm — a half-seated blade can fly off at highway speed. Rotate the blade back in line and ease the arm down.
🔧 Mechanic's note — Ray Delgado
From my bay, A half-seated connector on these HHRs will hold at idle and let go at 65 mph — give every new blade a hard tug along the arm before you drop it onto the glass.
5
Replace the passenger-side 18-inch blade
Repeat on the passenger side with the second 18-inch blade — release tab, slide-off direction, and click-on install are identical. After mounting, check from outside that both blades park neatly side by side at the windshield base without overlapping.
6
Replace the rear blade on the liftgate
The arm uses a Roc Loc 2 slot-and-tab mount — not the front J-hook — so a universal blade won't fit. Lift the arm, press the release tab, and slide the old blade off, noting which way the connector faces. Slide the new rear blade on.
7
Test front and rear wipers
Ignition on: test the front and rear washers, then run every wiper speed. Watch for streaks, chatter, or unwiped patches — a dirty windshield is the usual cause of chatter on new blades, so clean the glass if needed.
All Done!
Test your repair before closing everything up. If something doesn't work right, double-check your steps.
⚠️ Common Mistakes to Avoid
- • Assuming the rear is 11 inches on a 2010 or 2011 HHR — one fitment chart lists 12 inches for those years, so measure the old blade first.
- • Mixing up the identical 18-inch fronts — label which box is driver versus passenger, since the blades are the same length.
- • Forcing a universal rear blade onto the Roc Loc 2 arm — it needs the vehicle-specific blade with the matching connector.